#
#	Chandra Configuration
#	for NP-30J
#	AKIYAMA (akiyama@ma1.seikyou.ne.jp)
#

machine		"i386"
cpu		"I586_CPU"
ident		CHANDRA
maxusers	10

options		INET			#InterNETworking
options		FFS			#Berkeley Fast Filesystem
options		NFS			#Network Filesystem
options		MFS			#Memory Filesystem
options		MSDOSFS			#MSDOS Filesystem
options		"CD9660"		#ISO 9660 Filesystem
options		PROCFS			#Process filesystem
options		"COMPAT_43"		#Compatible with BSD 4.3 [KEEP THIS!]
options		SCSI_DELAY=15		#Be pessimistic about Joe SCSI device
options		BOUNCE_BUFFERS		#include support for DMA bounce buffers
options		UCONSOLE		#Allow users to grab the console
options		FAILSAFE		#Be conservative
options		USERCONFIG		#boot -c editor
options		VISUAL_USERCONFIG	#visual boot -c editor

# This provides support for System V shared memory.
#
options		SYSVSHM
options		SYSVSEM
options		SYSVMSG

# If your laptop have not had Windoze95-Ready BIOS, please update it.
# Such old BIOS'es sometimes have critical bugs at 32-bit protected
# mode APM BIOS interface (which have not used by Windoze 3.1).

# PC-card suspend/resume support (experimental)
options		APM_PCCARD_RESUME
options		PCIC_RESUME_RESET

# Keep power for serial cards when the system suspends
# (If your machine hangs up when you try to suspend the system with
#  FAX/Modem PCMCIA card, uncomment this option).
#options	SIO_SUSP_KEEP_PWR       

# Detach SCSI devices when the SCSI card is removed
options		SCSI_DETACH

# Detach ATAPI devices when the ATA card is removed
options		ATAPI_DETACH

# Japanese version of WaveLAN PCMCIA uses 2.4GHz band instead of 915MHz
# band that US version uses.  If you want to use Japanese version of
# WaveLAN, uncomment this line, or edit the corresponding config entry
# of /etc/pccard.conf.
#options	"WAVELAN_PCMCIA_24"

# Suspend the system when the battery status is "Low"
#options	"APM_BATT_LOW_SUSPEND"

# If you want to use NTP on laptop machines, uncomment the following 
# option.  Current APM implementation affects NTP client.
#options	"APM_NO_CLOCK_ADJUST"

# Some X-servers cannot survive suspend/resume on laptop.
# This option kicks her when the system is resumed from suspended mode.
options	SYSCONS_VTY_RESUME


config		kernel	root on wd0

controller	isa0
#controller	eisa0
controller	pci0

# Dont remove these two lines!
pseudo-device	card	1

# You must use "flags 0x1" when you don't hear any negotiation noise(?)
# if you use modem card, or pccardd doesn't read cis tuple, tell you 
# 'No card in database for"(null)"("(null)")' in case of Cirrus Logic's 
# pcic is your PC.
device		pcic0   at isa? port 0x3e4 irq 10 vector pcicintr
device		pcic1   at isa? port 0x3e2	# for HiNote Ultra II

controller	fdc0	at isa? port "IO_FD1" bio irq 6 drq 2 vector fdintr
disk		fd0	at fdc0 drive 0
# Unless you know very well what you're doing, leave ft0 at drive 2, or
# remove the line entirely if you don't need it.  Trying to configure
# it on another unit might cause surprises, see PR kern/7176.
#tape		ft0	at fdc0 drive 2

controller	wdc0	at isa? port "IO_WD1" bio irq 14 vector wdintr
disk		wd0	at wdc0 drive 0

controller	wdc1	at isa? port "IO_WD2" bio irq 15 vector wdintr
disk		wd1	at wdc1 drive 0

controller	wdc2	at isa? disable port "IO_WD2" bio irq 15 vector wdintr
disk		wd2	at wdc2 drive 0

controller	wdc3	at isa? disable port "IO_WD2" bio irq 15 vector wdintr
disk		wd3	at wdc3 drive 0

options		ATAPI		#Enable ATAPI support for IDE bus
options		ATAPI_STATIC	#Don't do it as an LKM
device		wcd0		#IDE CD-ROM
device		wfd0		#IDE floppy (LS-120)

# A single entry for any of these controllers (ncr, ahb, ahc, amd) is
# sufficient for any number of installed devices.

controller	aic0	at isa? port 0x340 bio irq 11 vector aicintr
controller	spc0	at isa? port 0x320 bio irq 11 iomem 0xd0000 flags 0x01 vector spcintr

# Future domain and Q-logic PC-card SCSI drivers 
# 	ported from NetBSD/pc98 (based on NetBSD 1.2)
options		SCSI_LOW	# XXX: for ncv? and stg? driver
controller	ncv0	at isa? port 0x320 bio irq 5 vector ncvintr
controller	stg0	at isa? port 0x320 bio irq 5 vector stgintr

controller	scbus0
device		sd0
device		od0	#See LINT for possible `od' options.
device		st0
device		cd0	#Only need one of these, the code dynamically grows

# syscons is the default console driver, resembling an SCO console
device		sc0	at isa? port "IO_KBD" tty irq 1 vector scintr
# If the screen flickers badly when the mouse pointer is moved, try this.
options		SC_BAD_FLICKER
# Enable this and PCVT_FREEBSD for pcvt vt220 compatible console driver
#device		vt0	at isa? port "IO_KBD" tty irq 1 vector pcrint
#options		XSERVER			# support for X server
#options		FAT_CURSOR		# start with block cursor
# If you have a ThinkPAD, uncomment this along with the rest of the PCVT lines
#options		PCVT_SCANSET=2		# IBM keyboards are non-std

# Mandatory, don't remove
device		npx0	at isa? port "IO_NPX" flags 0x1 irq 13 vector npxintr

#
# Laptop support (see LINT for more options)
#
device		apm0    at isa?		# Advanced Power Management
options		APM_BROKEN_STATCLOCK	# Workaround some buggy APM BIOS

device		sio0	at isa? port "IO_COM1" tty irq 4 vector siointr
device		sio1	at isa? port "IO_COM2" tty irq 3 vector siointr
device		sio2	at isa? disable port "IO_COM3" tty irq 5 vector siointr
device		sio3	at isa? disable port "IO_COM4" tty irq 9 vector siointr
device		sio4	at isa? disable port "IO_COM3" tty irq 5 vector siointr

device		lpt0	at isa? port? tty irq 7 vector lptintr

device		psm0	at isa? port "IO_KBD" conflicts tty irq 12 vector psmintr

# Order is important here due to intrusive probes, do *not* alphabetize
# this list of network interfaces until the probes have been fixed.
# Right now it appears that the ie0 must be probed before ep0. See
# revision 1.20 of this file.

device ed0 at isa? port 0x280 net irq 10 iomem 0xd8000 vector edintr
device ed1 at isa? disable port 0x300 net irq 10 iomem 0xd8000 vector edintr

# do not enable ze0 and zp0 (these devices are obsolete)
##device ze0 at isa? port 0x300 net irq 5 iomem 0xd8000 vector zeintr
##device zp0 at isa? port 0x300 net irq 10 iomem 0xd8000 vector zpintr

# IBM Smart Capture PCMCIA card
#device	scc0
#device	scc1

# Hitachi microcomputer system Speach Synthesizer card
#device hss0
#device hss1

# PCMCIA Joystick
#device		joy0	at isa? port "IO_GAME"

controller      snd0
device sb0      at isa? port 0x220 irq 5 drq 1 vector sbintr
device opl0     at isa? port 0x388

pseudo-device	loop
pseudo-device	ether
pseudo-device	log
pseudo-device	sl	1
# DHCP uses BPF (Berkeley Packet Filter)
pseudo-device   bpfilter        4
# ijppp uses tun instead of ppp device
#pseudo-device	ppp	1
pseudo-device	vn	1
pseudo-device	tun	1
pseudo-device	pty	16
pseudo-device	gzip		# Exec gzipped a.out's

options		DDB

# KTRACE enables the system-call tracing facility ktrace(2).
# This adds 4 KB bloat to your kernel, and slightly increases
# the costs of each syscall.
#options		KTRACE		#kernel tracing